ysi malaysia

Simplify turbidity measurements without compromising data quality!

YSI’s Turb® 750 T benchtop turbidity meter provides accurate and precise measurements up to 1100 FNU/NTU at an affordable price. The turbidity meter complies with EPA 180.

The IDS ProOBOD® self-stirring optical BOD probe for use with the YSI MultiLab. Designed to fit into standard 300 mL BOD bottles. EPA approved for wastewater compliance reporting of BOD and CBOD.
 

The ProOBOD is designed for use with all models of the YSI MultiLab, including the 4010-1W, 4010-2W, and 4010-3W.

Replacement Wiper

Replacement wiper for the EXO Central Wiper. Cleans sediment off of EXO smart sensor faces to extend long-term deployment times and ensure quality data. NOT compatible with EXO NitraLED.

Includes one wiper brush, screw, and hex wrench.

Wiper brush for use with EXO NitraLED UV Nitrate Sensor. Installs on EXO Central Wiper (not included).
 

New wiper brush with unique arm extension for cleaning the EXO NitraLED sample path. The main brush cleans all other EXO smart sensors to ensure data quality for extended long-term deployments.

Compatible with any EXO Central Wiper.

Copper tape provides biofouling protection
 

Copper tape for water quality sondes and sensors provides biofouling protection and extends deployments.

• 2 inches wide and 16 feet long (5 cm x 4.

Specially designed cleaning brush for the EXO Conductivity & Temperature Smart Sensor (#599870-01).
Fits inside the flow cell of the sensor to remove bio-fouling and other contaminants. 

Kit includes two cleaning brushes.

O-Ring grease

This silicone based lubricant helps ensure a watertight seal on YSI water quality instruments and sensors.
Includes one 0.5 oz tube of lubricant.

Note: Be sure to follow lubrication instructions carefully when applying Krytox®.  Too much or too little can undermine the effectiveness of the lubricant.

The cable grip is designed to clamp onto vented or non-vented field cables for instrument retention.
 

The EXO Cable Strain Relief is designed to add redundant protection to your Field Cable, Flying Lead Field Cable, or Vented Flying Lead Field Cable for EXO systems.

The cable grip is designed to clamp onto vented or non-vented field cables for instrument retention.
 

The EXO Cable Strain Relief is designed to add redundant protection to your Field Cable, Flying Lead Field Cable, or Vented Flying Lead Field Cable for EXO systems.

Alignment Ring for EXO2 and EXO3 Sondes holds the sensors tightly together minimizing wiggle during the wipe cycle.
 

Alignment Ring required for EXO NitraLED use on EXO2 and EXO3 Sondes.

Includes one alignment ring, 10 small o-rings and 10 large o-rings.

The ProSwap Logger Power Pack is designed to supply top-side power to ProSwap Loggers that do not have a built-in battery.
The Power Pack provides power to the ProSwap Logger using six AA alkaline batteries.
 

The ProSwap Logger Power Pack provides dedicated external power with six AA alkaline batteries for the ProSwap Logger Sonde.

ProDSS Small, Hard-sided Carrying Case
 

Fits 1 and 4 meter cables, handheld, flow cell and accessories.

Case dimensions: 18 x 13 x 7 inches

A removable foam insert is pre-installed for smaller diameter cables such as the ProDSS ODO/CT field cable.

ProDSS Large, Hard Sided Carrying Case
 

Fits 10, 20 and 30 meter cable with cable management kit, handheld and accessories.

Case dimensions: 19 x 14 x 8 inches

A removable foam insert is pre-installed for smaller diameter cables such as the ProDSS ODO/CT field cable.

Connects ProDSS to USB stick, included with instrument.

 into the field with the ProDSS. We hope to see you in class!

Connects ProDSS to AC charger or PC, included with instrument and battery charger kit.

Includes Li-ion battery pack for installing in ProDSS and replacement gasket.

Polarographic, membrane-covered BOD Probe, self-stirring, 1.5m (5 ft) cable.

The 4100 BOD probe can only be used with the MultiLab 4010-1W, MultiLab 4010-2W, and the MultiLab 4010-3W. It can also be used with the MultiLab 4010-1 if the latest instrument firmware has been installed

The TruLine Ammonia ISE features BNC connection and can be used with the YSI TruLab 1320. It can also be used with the YSI MultiLab 4010-2 or 4010-3 if a BNC adapter is installed.

The TruLine Ammonia laboratory electrode kit includes a gas-sensing ammonia combination ISE, 2 membrane modules (i.e.